How to base a Paver Patio | Paver driveway in minneapolis, MN
Start by Marking out the area with a garden hose and placing outdoor furniture is a great visualization tool to make sure you are making the area large enough for its intended use. Sketch your patio on a piece of graph paper showing all important dimensions and permanent structures to make calculating your materials a cinch later.
Determine the type of paving you would like to use.
Urban Landworks offers plenty of options of natural stone such as flagstone & steppers, and many concrete & clay paver options from Anchor, Borgert, Interlock, Pine Hall, Rochester Concrete, We have all the paving options on display and quite a few actually installed on the grounds at Gertens, so please stop by & check ‘em out to help you make a decision. Another thing to consider would be whether you would like accent or border pieces either inlayed or surrounding your patio. It is a good rule of thumb to take cues from the style of your home as well as siding and trim colors when deciding which style and color paving material to go with.
Outline the area of your patio with marking paint. Note that you will need to mark 4”-6” out from the edge of where you want your pavers to account for base material and edging. Before you start digging the base, make sure to call your utility company (here in MN it is Gopher State One at 800.252.1166 or go online at gopherstateonecall.org) and have them come mark any underground utilities in the area.
The more time and effort put in to preparing the base for you patio correctly, the better your patio will perform and the longer it will last. You will need to dig down 9 inches to account for the depth of your base materials and pavers. There will be 6” depth layer of Class 5 gravel, 1” depth layer of washed sand, and 2.5” thick pavers. Make sure to account for drainage when excavating your base. You want all rainwater to run away from your house or any existing structures. To accomplish this, there should be at least a 1/8”-1/4” drop for every linear foot away from the house.
Once the area is excavated and rough graded, use a plate compactor to go over the entire area and make sure the ground is firm. If you choose to install geotextile fabric under your gravel, now is the time to lay it down. When adding the Class 5 Gravel, spread a layer of the gravel 2 inches deep over the entire surface using your flat shovel a rake. If the gravel is completely dry and dusty, lightly spray it with your garden hose to cut down the dust and make it easier to spread with the rake. Go over the entire area with the plate compactor, making sure to overlap each pass by about 3 inches. Spread another 2 inches of gravel, and repeat until all the gravel is installed. Pull string lines over your base at the final surface elevation and slope of your patio. There should be a 3 inch gap between the top of the gravel and the string line. Check the base in this manner in at least 2 spots to make sure your gravel is level.
Place edge restraints along all open edges (edges not against a curb, house, or other paving). Secure the edges in place with 10 inch timber spikes driven into the class 5 gravel every 2 feet at minimum. Edging for areas that are curved can be installed after the pavers are laid, but before final compaction.
Only spread and screed the sand once you are ready to start laying pavers or stone. Otherwise any rain will ruin the screeding, and the sand can become a bathroom for any neighborhood animals. That does NOT make for a fun installation experience! You will need to install the sand as you go to prevent walking on and disturbing the level sand as you lay the pavers, so make sure to start in a 90° corner if you can. To install the sand, place the 1” diameter PVC pipes several feet apart and parallel to each other directly on the class 5 gravel. Spread sand between the PVC pipes using your shovel and rake to loosely level it. Place the 2x4 timber on top of the pipes, and pull it across the surface several times until the sand is perfectly smooth. Remove the pipes, fill in the indentations with sand and level it with the trowel.
Laying Paver Stones
Again, start in a corner if you are able. Remove the string lines from checking your grade, and reposition them to be used to make sure your joint lines (the small gap between pavers) are straight. Set up the string lines about every 4’ or so to ensure your joints are straight across the entire patio. Work from right to left then left to right, one row of pavers at a time, installing any borders first. Set the pavers lightly into the sand, do not press or hammer in. Try not to walk or kneel on the pavers before they are vibrated in with the plate compactor to ensure they will not settle unevenly. Make sure to check the straightness of your joints against the string line regularly. Otherwise just keep screeding the bedding sand, laying the pavers, and maintaining consistent joint widths. You will most likely need to make some cuts at some point. Have no fear, the masonry cutting saw may seem intimidating, but is very safe and easy to use. Place as many full sized pieces up to the edge as possible, then hold the piece that needs to be cut in place and mark the portion that needs to be cut off with a piece of chalk. Make sure to put on your hearing and eye protection, and make your cuts. Once all the pavers are in place it is time to do the final compaction. Make sure not to scuff the surface of your pavers by placing cardboard, a carpet remnant, or a rubber mat between the compactor and the pavers. Adjust joints to be consistent as needed, and replace any pavers that may have cracked during compaction. Now it is time to fill the joints. You can either use the same washed sand as you used for the bedding sand, or choose to use Polymeric Joint Sand. Polymeric Sand has many advantages including inhibiting weed growth and ant hills in your paver joints. Make sure to follow the manufacturer’s instructions when installing Polymeric Sand.
Finishing Up and Aftercare
Bring in soil to backfill the area above your edging between your new patio and the existing lawn. Keep the soil about ½” below the patio to make sure to allow rainwater runoff. You can either incorporate this area in to a new planting bed, or seed or sod new lawn. Depending on the look you’re going for, and the functions your patio will serve you may choose to seal your patio. Urban Landworks offers many types of sealers from invisible, to color enhancing, to a glossy wet look. Make sure to use a hardscape cleaner prior to sealing your patio to ensure any stains are gone, and that the sealer will make a good bond with the pavers. Aside from that, sit back, relax, and invite some friends over so you can show off your new outdoor look.
12/14/2021 10:00:50 pm
I found this article very informative about "". Looking forward for more informative articles like this related to <b><a href="https://advanceddrivewaysolutions.co.uk/" rel="dofollow">Fencing & Resin Drives Solutions Blackpool
1/25/2022 07:01:47 am
I had no idea that different paving materials can improve the appearance of your garden. My mom wants a modern yet natural-looking outdoor space where she can entertain guests. Maybe we should find a paving expert that could help us with this in the future!
1/28/2022 07:29:58 am
If the gravel is completely dry and dusty, lightly spray it with your garden hose to cut down the dust and make it easier to spread with the rake. Thank you for making this such an awesome post!
4/4/2022 07:16:29 pm
It's my pleasure to find this amazing website who provides mostly unseen information about every single topic which is i really like it.
5/4/2022 05:15:17 pm
I appreciate what you said about how urban landmarks require regular sealcoating. I need to get a contractor to help me with my driveway. It needs to be resealed.
1/26/2023 06:23:07 am
I want to get a nice walkway installed, but I want to make sure that the pavers last me a long time. It's good to know that using sand as a base would be important. That seems like a great way to ensure that my pavers are stable.
4/17/2023 11:45:57 am
The pavers lightly into the sand, do not press or hammer in. Try not to walk or kneel on the pavers before they are vibrated in with the plate compactor to ensure they will not settle unevenly. Thank you for making this such an awesome post!
Leave a Reply.
Written by: Managers and partners of Urban Landworks